The transmission parameters of all kinds of HSTC such as power flow,torque ratio,power split ratio and efficiency were compared.
基于2K-H型行星轮系的运动方程,给出了分流式液力机械变矩器(HSTC)自锁的判断方法;提出了HSTC功率流的分析方法;建立了HSTC的结构参数与传动参数之间的关系,对比分析了各种型式的HSTC的效率、变矩比、分流比等传动参数。
In addition,we present the relation curves of bending moment ratio .
本文应用材料力学与弹塑性力学理论,分阶段推导了电梯导轨T型钢进入弹塑性弯曲变形时中性层的变化规律及弯矩的表达式,给出了弯矩比与弹区比的关系式,为其矫直参数的设计计算提供一定的参考。
The optimized adoption methods of plastic bending moment ratio are derived to make the anti-crack capability best and the mount of steel least separately for reinforced concrete slab bottom based on Navier solution and steel optimization of the thin-slab theory.
基于薄板理论的Navier解和钢筋优化分析,分别建立了保证钢筋混凝土板板底抗裂性能最优和配筋量最少的塑性弯矩比取值优化方法。
Weighted linear combination (WLC) of MCE in IDRISI software is introduced, and analytical hierarchy program (AHP) is applied to construct comparison matrix, so the weights of disaster factors are derived from AHP weight derivation.
通过引入IDR ISI软件多准则评价(MCE)中的权重线性组合法(WLC),应用层次分析程序(AHP)构建比较矩阵来计算各地质灾害因子的权重系数。
Based on the concentration of the comparison matrix judged by the general partners, this paper develops a non linear programming model for the stage investment of venture capital fund and presents a method for determining the stage investment weights.
在集结一般合伙人比较矩阵的基础上建立了风险投资基金分段投资非线性规划模型 ,并给出了分段投资比例的计算方
on the correlation, and introducing the dynamic comparison matrix to calculate the corresponding weighting coefficients,the algorithm can analyzes the topic information in the Web page objectively,and guarantee retrieval result rationality.
该算法考虑了超文本标记、锚文本、文本内容等对相关性的影响,引入动态比较矩阵来计算相应的权重系数,能够客观分析网页所包含的主题信息,使检索结果排序更合理。
Aseismic Capacity of Frame-Shear Wall Structures with Different Percentages of Overturning Moment Resisted by Frame
框架倾覆弯矩比例对框架—剪力墙结构抗震性能的影响
COMPARATIVE STUDY ON BENDING STRENGTHENING METHOD OF NEGATIVE MOMENT AREA AT BEAM END IN RC FRAME
梁端负弯矩区受弯性能加固方法对比试验研究
The actual stress is not proportional to the bending moment.
实际上应力与弯矩不成正比。
Analysis on the moment transferring factor of RC out-of-plane beam-wall joint
钢筋混凝土梁-墙直交节点弯矩传递比例分析
Analysis and Comparison of Displacement Impact Coefficient with Moment Impact Coefficient of Simple-supported Beam
简支梁位移冲击系数与弯矩冲击系数大小分析与比较
Comparison of the Spline-based Method of Cubic Spline Function and the Similarities and Differences of Three-moment Method
三次样条函数的基样条法和三弯矩法之异同比较
Pushover analysis on rectangular column frames with different column-to-beam strength ratios
RC矩形柱框架结构不同柱-梁抗弯强度比的Pushover分析
The beams are designed with respect to the bending moment.
梁是按照弯矩设计的。
On the influence of the bending moment waveform disturbance on the pure bending beam flexion
弯矩波形扰动对纯弯梁弯扭屈曲的影响
The Calculatiou of critical load by torsion angle-bending moment matix;
用转角弯矩矩阵确定压杆的临界荷载
The simplified calculation formula form of cracking moment is simple and the analytical results agree well with that of experiments.
经简化后的开裂弯矩计算公式形式比较简单,计算结果与试验结果基本吻合。
The Influence of Cold-Formed Effect to Stress Capacity Performance of Cold-Formed Rectangular Hollow Section Beams;
冷弯效应对冷弯矩形钢管梁受力性能的影响
Research on the Curves Versus Moment Hysteretic Behavior of Thin-walled Cold-formed Steel Beams
冷弯薄壁型钢梁的弯矩-曲率滞回性能试验研究
Calculation for Cracking Moment of SRC Flexural Member
型钢混凝土受弯构件开裂弯矩的计算初探
Study of plastic limit load of the combined fittings of double elbows under in-plane bending moment
面内弯矩下双弯头组合管件的极限载荷研究
Bending moments produced by lift generally have only a small effect on the resultant bending moment.
一般由升力所产生的弯矩对最终的弯矩只有很小的影响。
Torque and Bending Moment in a Shaft with Combined Deformation Measured by Resistance Strain Gauge Method
电阻应变计法测量组合变形轴的扭矩和弯矩
ANALYSIS OF COMPOSITE BENDING MOMENT DIRGRAMS UNDER BENDING AND BENDING DEFORMATON FOR ROUND SHAFT;
关于圆轴含有弯弯组合的合成弯矩图形状的讨论
