A wide range of standard stampings, non-standard products, stainless steel washers, internal/ external teeth washers, rings, circlips for holes, circlips for shaft, other fasteners, fittings, seal washers and clamps主要生产各种标准件冲压件.各种非标产品.
不绣钢垫圈;内外齿垫圈;挡圈;孔用挡圈;轴用挡圈;纱嘴头,其他紧固件、接件密封垫圈卡圈.
The primary function of sealing gasket is to prevent gas from leakage.
密封垫圈的主要作用是防止气体泄漏。
The hard sealing gasket also can absorb the noise and vibration.
⑵密封垫圈也可吸收噪音及振动。
Bite type tube fittings--Tipping washer
GB/T3762-1983卡套式管接头用尖角密封垫圈
Our customers are mainly from the automotive, medical and healthcare, home electronics and hard disk drive industries.
·硬盘电子设备和其他电子设备的精密密封垫圈。
a gasket to seal a cylinder head.
一种密封汽缸盖顶的垫圈。
If an adequate seal cannot be made, try a new washer.
如果不能达到充分的密封，试一个新垫圈。
Apply silicon sealer/lubricant to the inner and outer diameters of the flange kit gasket, and press the gasket onto the valve body end.
将硅密封/润滑剂施加在法兰组件垫圈的内径和外径上，将垫圈压在阀体端口上。
a gasket consisting of a flat ring of rubber or plastic; used to seal a joint against high pressure.
一种由橡胶或塑料的扁环组成的垫圈；用于密封抗高压的接点。
Stainless steel stuffing box hardware is standard (ie. bolts, gland studs, nuts, washers).
标准的金属密封不锈钢填料箱（如螺栓、填料压盖螺栓、螺母、垫圈）。
Pressure Seal– uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal.
(3) 压力密封–结构简单，分段扣环，镀银低碳钢垫圈，有助于拆卸和最大限度的阀帽密封。
Trim or remove excess sealant film in the rear main cap oil pan gasket groovDO NOT remove the sealant inside the rear main cap slots.
修整或清除后主盖机油底壳垫圈凹槽中过多的密封剂薄膜。切勿清除在后主盖槽中的密封剂。
Pressure Seal ? uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal.
压力密封?结构简单，分段扣环，镀银低碳钢垫圈，有助于拆卸和最大限度的阀帽密封。
chev(e)ron ring
人字密封圈, v型圈
Sufficient force is required to push the metal sealing surfaces into the washer; too much force will damage the bead surfaces.
要求足够的力量来把金属密封表面推进垫圈，但太大的力量会损伤垫珠表面。
joint gasket- or packing- type, of laminated metal foil
层压金属箔密封或填密封式接合衬垫
Neoprene grommet and complete epoxy encapsulation provide for a true non-wicking cable entry. An isolating cable chamber is not needed.
氯丁橡胶绝缘垫圈和全部环氧树脂密封，提供真正的无芯电缆连接。不需要另外配置绝缘电缆盒。
Our standard gasket is double jacketed metal.
我们标准的垫圈是双重封装的金属。
